What are the precautions for engraving machines in daily use?
Slurry Pump includes horizontal slurry pump, vertical slurry pump, submersible slurry pump, etc. For horizontal slurry pump, there are metal slurry pump and rubber lined slurry pump.
Slurry Pump,Centrifugal Slurry Pump,Horizontal Sludge Pump,Horizontal Centrifugal Slurry Pump,Centrifugal Pump Theory Slurry Pump,Heavy Duty Centrifugal Slurry Pump Shijiazhuang Boda Industrial Pump Co., Ltd. , https://www.mineralslurrypump.com
Second, the installation of materials must be solid, must follow the "fitting, loading, leveling" principle, is strictly prohibited in the material hanging in the place of carving.
3. When installing the card tools, the dust and debris in the card head must be cleaned first, and then the card head should be inserted into the pressure cap and placed in positive position. Then the motor head should be mounted on the motor spindle and the tool should be inserted into the chuck. Press the cap. When the upper and lower knives are tightly pressed, it is forbidden to use a push-pull method but a rotary method. When cutting the knife, clean the pressure cap and the turning waste, then loosen the pressure cap to remove the tool and unscrew the pressure cap to remove the chuck.
Fourth, when the tool is installed, the length of the tool exposed head must be determined by the engraving depth file and the fixture. When the condition is satisfied, the length of the exposed head is as short as possible. When the total length of the tool is less than 22 mm, the use of the head is prohibited.
5. When inserting a cutter, the length of the holder into the chuck must be greater than 18mm.
Sixth, in the processing, if the cutting fluid must be flushed to the tool.
7. During the carving process, close observations are strictly prohibited to prevent the chips from flying into the eyes. To pause the engraving while watching, turn off the motor spindle and make sure that the motor spindle is no longer rotating. During the carving process, it is forbidden to cut the surface by hand, and it is forbidden to wipe the work surface with a cotton thread.
8. It is forbidden to place any item on the machine table or the beam; it is prohibited to hold it on the machine bed such as the cross beam and the protective cover; the body is forbidden to rest on the machine bed.
Nine, is strictly prohibited knock, hit the motor shaft, unloading knife is strictly prohibited.
10. Do not use the machine in an overheated or undercooled state.
XI. The carving machine is a kind of light processing equipment. The sum of the fixtures, the weight of the workpiece, and the processing waste should not exceed the rated weight of the machine tool.
Twelve, before carving carefully check the size of the tool used, whether the performance meets the programming requirements.
Thirteen, carefully check the tool path before processing.
14. Be sure to confirm the correct starting point (work origin) for each axis before starting processing.
15. The motor shaft must be rested for 2 hours every day.
16. It is strictly forbidden to insert and insert wires, cards and electrical devices with electricity; when processing flammable materials such as organic materials, there must be effective fire prevention measures at the work site.
17. Lubricate the machine tool and clean the machine tool 10 minutes before work every day. Make sure the machine stops, stop the machine at the specified position, turn off the power, and confirm that all switches are off before leaving.
Horizontal Metal slurry pumps are cantilevered slurry pumps, Horizontal Centrifugal Slurry Pump, Centrifugal Pump Theory Slurry Pump, Heavy Duty Centrifugal Slurry Pump. They are designed for the handling highly abrasive, high density slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. The pumps of this type also may be installed in multistage series.
The frame plates have replaceable wear-resistant metal liners. The impellers are made of wear-resistant high chrome alloy .
Horizontal Metal slurry pumps may be adoptable of gland seal or expeller seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
Rubber Lined Slurry Pumps and spare parts can fully interchange with world famous brand. These pumps are of heavy-duty construction, designed for continuous pumping of highly abrasive and corrosive slurries. They feature a wide choice of replaceable abrasion resistant metal or moulded elastomer casting liners and impellers, which are all interchangeable within a common costing assembly.
BV pumps are vertical, centrifugal slurry pumps submerged in sump to work. They are designed for delivering abrasive,large particle and high density slurries. These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties. Wet parts of type BV pump are made of abrasion-resistant metal. All parts of type BVR pump immersed in liquid are lined with rubber outer liner. They are suited to transport non-edge angle abrasive slurry.
ZQ(R) series of slurry pumps are hydraulic devices composed of coaxial motors and pumps that are submerged in the fluid to work. These pumps are characterized by unique structure wide passage, high capacity of removing sewage, and high quality materials, offering excellent corrosion resistance. They are suitable for transferring the liquid containing solid particles, like sand, coal slag, and tailings, and removing slurries in metallurgical plants,mines, steel mills, or power plants, as an ideal alternative to traditional pumps for taking away slurries
