The traffic rules that you neglected must be seen!
I believe that people who drive have all encountered violations that have been inexplicably deducted. Many times they are penalized for fines or demerit points. They still do not know why, but many times are caused by wrong driving habits and some easily overlooked rules. Too close to the car was hit by a red light If this is the first place worth mentioning, it is better to be the first person, especially if there are trucks, buses or some relatively tall cars. The sight is completely blocked, but the car in front of it is rushing through the yellow light. At this time, you will follow and rush over in the back. Although this violation may eventually be appealed in the traffic police department, it is also troublesome. So keep the distance when you encounter the big car, pull down the distance when you do not see the indicator light, and wait until you see it. High speed ramp, speeding more than 50% If you have a camera license, you must pay attention to it. If you have a camera license, you must pay great attention to it. In many cases, the speed limit of the ramp is even lower than in the urban area. If you have just gotten from a high speed, the speed will not be low, so it will be 50% or more. Not surprising, but 12 were gone. Going too fast at high speed is also punished Everyone knows that we can't speed, but it's illegal to go too slowly. Usually, high-speed speed limits have a maximum speed limit and a minimum speed limit. If the speed limit is lower than the minimum speed limit, it will be punished. Therefore, it is not always better on the freeway, especially for beginners. Green light does not go is also illegal There are six red lights, but if the green light does not go away deliberately, it will be considered as disturbing the traffic order, and 3 fines will be deducted. Right-turn vehicle violates regulations and judges the accident At the intersection, the first turn in all directions is well defined. But the most likely mistake is the relative direction. When a right-turn vehicle meets a left-turn vehicle, many times the driver thinks who should go first, but according to regulations, this situation should be a right-turn car that allows the left-turn car to go first. If an accident occurs at this time, turn right. If the car is not allowed, it will be determined that the right-turn car is full responsibility for the accident, so be sure to humility when driving right. The so-called aligning bearing is that the raceway raceway is spherical, and it can adapt to the angular displacement between the two raceways, which is mainly supported by radial load, and can also bear a small number of two-way axial loads.
Tune ball bearing editing
Spherical Roller Bearings Self Aligning Bearing,Self Aligning Ball Bearing,Self Aligning Roller Bearing,Self Centering Bearing LUOYANG AUTO BEARING CO.,LTD , https://www.lyautobearing.com
Characteristics of core bearing
It is mainly subjected to radial load, and it can also bear a small amount of bidirectional axial load.
The center ball bearing is the inner ring of the two raceways and the outer ring of the raceway for the spherical surface, and the ball bearing is assembled with a ball shaped roller. It can bear a large radial load and also bear a certain axial load, as shown in Figure 1. The outer raceway of this kind of bearing is spherical, so it has the performance of adjusting center.
The main features of the ball bearing are as follows:
(1) the outer race raceway of the ball aligning ball bearing is a part of the sphere. The center of curvature is on the bearing axis. Therefore, the bearing has the function of adjusting the center, and it can be automatically adjusted when the shaft and shell appear flexure, and does not increase the bearing burden.
(2) an appropriate amount of axial load that can bear radial load and two directions. But it can't bear the torque load.
This kind of bearing has smaller contact angle, almost no contact angle under axial load, small axial load capacity, large radial load capacity, and suitable for heavy load and impact load.
(3) the double row center ball bearing with tightened and locking nuts can be installed at any position on the optical axis and does not need to be positioned on the shoulder.
Spherical Roller Bearing is in the two groove of the inner ring and outer ring raceways between Spherical Bearing assembly, a drum shaped roller, as shown in figure 3. Spherical Roller Bearing with two rollers, mainly bear radial load, also can withstand any direction of the amount of axial load; radial load capacity is very high, especially suitable for radial heavy loads or vibration, but unable to bear pure axial load.
The main characteristics of the spherical roller bearing:
(1) bearing with self-aligning ball like outer ring spherical roller bearing raceway is a part of spherical surface, the curvature center on the bearing axis, the bearing outer ring raceway is spherical shape, so its self-aligning performance is good, can compensate concentricity error, thus can realize the automatic aligning.
(2) in the section perpendicular to the rolling direction, the roller busbar is a curve, which fits well with the inside and outside raceway. The roller and raceway are linear contacts, which can bear radial load and axial load, and has good impact resistance.
(3) roller and roller bearing raceway match well, and are therefore relatively serious curve generatrix, sliding, friction than cylindrical roller bearings, spherical roller bearings are allowed so low working speed.
(4) the heart fades with a normal roller bearing non symmetrical roller, it will generate an axial force, roller by the force and the center fixed flange contact, spherical roller bearing symmetrical roller, it can move along the axial direction using the middle movable baffle ring, so no longer block roller center the edge of the constraints, and saves the recess of the inner raceway, the roller can be used longer, so as to improve the bearing capacity.
(5) single row self-aligning roller bearing contact angle is 0. Under axial load, the contact angle did not change significantly, the axial load will be very small contact forces generated great between roller and raceway, so when the axial load is greater than the radial load, the loads of single row spherical roller bearing can bear radial and axial.
(6) bearing with self-aligning ball like set with tight double row spherical roller bearing can be installed in any position on the optical axis, do not need to process the positioning shaft shoulder.
